产品特性:高灵敏 | 品牌:鑫永诚 | 型号:XYC-IR3A940AC |
封装:DIP | 批号:2020+ | 配置类型:红外 |
峰值反向电压:5v | 最大浪涌电流:1000mA | 正向电压(Vf):1.3-1.6v |
正向电流(If):20mA | 反向电流(Ir):5 | 恢复时间:0.001NS(纳秒) |
工作温度范围:-25--+85° | 应用领域:智能家居 | 是否定制:是 |
是否跨境出口:否 | 材质:环氧树脂 | 温度系数:PTC |
产品性质:热销 |
(XYC-IR3A940AC )3mm红外发射接收管:
产品应用图:
产品说明:
鑫永诚IR940红外LED是一款低功耗,插件式外型封装的二极管,它具有发射功率强、受光角度均匀等优点。NEWOPTOIR940infraredLEDisalowpowerconsumptiondiodeinDIPpackage.Thismodelhastheadvantagesofstrongtransmittingpoweranduniformlightangle.
特性Features
■峰值波长940nmPeakwavelengthλp=940nm
■高可靠性Highreliability
■低功耗LowPowerConsumption
■符合RoHSRoHScompliant
应用Applications
■红外摇控发射电子产品Infraredremotecontroltransmitterelectronicproducts
■遥控器信号发射SignalEmittingofRemotecontrol
■安防摄像头和网络摄像头补光CCTVandIPCamera
■信号传输Signaltransmission
量身订制Customization
■品种齐全,生产周期短,小批量库存备货Completevarieties,shortproductioncycle,smallbatchinventory
■可按要求提供不同外型,角度,方便安装于产品的任何位置Customizedifferentshapesandangles
■可按需求提供的规格,以便让产品效果更好,更具市场竞争力Customizemostsuitablespecificationstomaketheproductbemorecompetitive
注意事项:
●本产品不适合做回流焊接。It’sunsuitableforreflowsoldering.
●手工焊接只可焊接一次。Manuallysolderingshouldbedoneonceonly
●器件外部温度在40℃以下时,才可以对其进行处理。避免高温时操作对LED造成损伤。PleasesoldertheLEDunder40degreetoavoidhightemperaturedamagethedevice
●在焊接温度回到正常以前,必须避免使LED受到任何震动或外力AftersolderingtheLED,pleasekeepitoutofanyshakeorouterforcebeforeitcometonormaltemperature
●在焊接后推荐使用酒精进行清洗,在温度不高于30℃的条件下持续1分钟,不高于50℃的条件下持续30秒。使用其他类似溶剂清洗前,请先确认使用的溶剂不会对LED的封装和环氧树脂部分造成损伤。ItisrecommendedthattousealcoholcleanLEDaftersoldering.Cleaningshouldbedoneunder30℃for1minuteor50℃for30seconds.Whenusingothersolvents,pleaseconfirmwhetherthesolventswoulddissolvethepackageorresinbeforehand.